How To Change Water Filter In Whirlpool French Door Refrigerator?

Your Whirlpool French Door refrigerator water filter works hard to provide tasty, healthy, and safe water. Nowadays, almost all modern fridges come with water filtration technology.

Cloudy refrigerator water means that the filter needs to be replaced. It is essential to change your water filter every 200 gallons (six months).

You can easily replace the water filter in your Whirlpool French Door refrigerator on your own, so keep reading to find out how to do it.

Finding The Water Filter For Your Whirlpool French Door Refrigerator (Filter Types)

Before going to replace it, you must know which filter is for your refrigerator. There are 5 filters for your fridge. You have to choose the right one for your fridge:

  • Filter 1
  • Filter 2
  • Filter 3
  • Filter 4
  • Filter 5

How To Change Water Filter 1 In Whirlpool French Door Refrigerator:

After you have find that the refrigerator needs a filter 1 to replace, then follow these steps to replace the water filter 

  1. Locate The Water Filter Cover: Start by finding the filter inside the cooling chamber. You will find it in the top-right corner of the chamber.
  2. Discard The Old Filter: Now, pull the filter out and discard it by opening and lifting the door up.
  3. Open Your New Filter: The O-rings are protected by protective covers. Remove these covers and open the new filter. Once the body has been removed, make sure the O-rings are still in place.
  4. Inserting The New Filter: Ensure that the arrow points upward when inserting the new filter into the slot. The water filter should not be forced. If it doesn’t slide in smoothly, rotate it until its notches are correctly aligned with its grooves. Note: Don’t exert too much pressure on the filter while inserting because too much pressure can break the filter.
  5. Close The Filter Door: After inserting the new filter, close the door of the filter, so it snaps into place.
  6. Run Couple Of Gallons Of Water: Run a couple of gallons of water through the water line to flush out any carbon particles that may have come loose in shipment.

Read More: Pro Tips To Clean Water Filter Cartridge

How To Replace Water Whirlpool French Door Refrigerator Filter 2

If your refrigerator requires filter 2 to replace, then you have to follow these steps to replace its water filter:

  1. Locate Your Water Filter Cover: The first step is to locate the water filter cover in the upper right-hand corner of the refrigerator.
  2. Discard The Old Filter: Now, after finding the filter door, you have to discard the old filter. Do it by opening the filter door. Turn the filter left and pull it down until it’s angled down. Remove the old filter and dispose of it.
  3. Open The New Filter: The first step is removing the protective coverings from your new filter’s O-rings. Once the cover has been removed, make sure the O-rings are still in place.
  4. Insert The New Filter: Now insert the new filter. Make sure the arrow points upwards when you insert the new filter into the filter slot. Pushing in will cause the filter to rotate.
  5. Close The Filter Door: Lock the filter by turning it clockwise and seal the filter door by pushing it closed.
  6. Run Couple Of Gallons Of Water: Run a couple of gallons of water through the water line to flush out any carbon particles that may have come loose in shipment.

How To replace Whirlpool French Door Refrigerator Filter 3

If your refrigerator supports filter 3 to replace, then you have to follow these steps to replace its water filter:

  1. Locate The Filter Cover And Discard The Old Filter: Firstly, locate the filter cover. The filter cover for the refrigerator’s water can be found on the left side of the base grille. To release the filter, you need to push the eject button. Then, remove and discard the filter.
  2. Open The New Filter: You need to remove the O-ring protectors from your new filter. Once the cover is removed, ensure that the O-rings are still attached.
  3. Insert The New Filter: Place the filter cap on top of the new cartridge so the ridges will align. Lock the cap in place by turning it clockwise. Make sure the arrow points are left when inserting the new filter into the slot.
  4. Close The Filter Door: After the whole process, you have to push the filter in until the eject button pops back out. And now, close the door of the filter cover.
  5. Run Couple Of Gallons Of Water: Flow a few gallons of water through the water line to flush out any carbon particles that may have come loose during shipping.

How To Replace Whirlpool French Door Refrigerator Filter 4

Follow these steps if your refrigerator supports filter 4 to replace its water filter:

  1. Locate And Open The Water Filter Cover: Your water filter cover should be located in the upper right-hand corner of your refrigerator. Pull the cover down if the filter tab on your refrigerator is facing outward. The small lever at the bottom of the cover can be pulled forward and down to open it.
  2. Discard The Old Filter: After locating and opening the cover door, you have to discard the old filter. Pull the filter left to turn it. Throw away the old filter.
  3. Pull Out A Cap From Inside: Insert the new filter into the slot by aligning it with the grooves, pushing it in, and turning it to the right.
  4. Close The Door: To lock the filter, you need to push it up. To close the filter door, push it up, and it will snap shut.
  5. Run Couple Of Gallons Of Water: Repeat the same process to run a few gallons of water.

Read More: Best Water Filter For Fridge

How To Replace Whirlpool French Door Refrigerator Water Filter 5

Follow these steps if your refrigerator supports filter 5 to replace its water filter:

  1. Locate And Open The Filter Door: The water filter cartridge cap is located on the left side of the refrigerator’s base grille. Remove the cap by rotating the handle counterclockwise until it is vertical, then pull it straight out.
  2. Discard The Old Filter: The filter cap can be removed by sliding it off the end of the filter. The old filter should be discarded, but the cap should be kept.
  3. Open The New Filter: The O-rings are protected by protective covers. Remove these covers and open the filter. Replace the cartridge cap on the new filter.
  4. Insert The New Filter And Close The Cover: Be sure to insert the cap handle into the filter slot when inserting the new filter. Make sure you push in. Once you’ve oriented it horizontally, rotate it clockwise. Now close the filter cover.
  5. Run Couple Of Gallons Of Water: Repeat the same process to run a few gallons of water.

Protect Your Refrigerator By Cleaning The Condenser Coils

Refrigerators can run hotter or even shorten their lifespan when their condenser coils are clogged. For this reason, it’s important to clean your refrigerator’s condenser coils to prevent clogging from dirt, dust, and pet hair.

Some models don’t need to be cleaned, an owner can clean some, and others require a certified technician. The condenser coils cannot efficiently release heat when they are clogged, which causes your refrigerator to run warmer and makes your compressor work harder. As a result, your refrigerator may have a shorter lifespan.

How To Clean The Condenser Coil on Whirlpool Refrigerator?

Follow these steps to clean your condenser coil:

1. The best way to clean condenser coils is with a vacuum and a soft brush. Disconnect your refrigerator’s power or plug it out to clean the condenser coils.

2. Take off the refrigerator’s bottom grille. Make sure you clean the grill, the open areas behind it, and the front surface of the grill with a vacuum cleaner and soft brush.

3. Plugin or reconnect the refrigerator and the base grille.

4. The condenser may need to be cleaned every two to three months if the environment is particularly greasy or dusty or has significant pet traffic.

When To Replace The Water Filter In Whirlpool French Door Refrigerator

The Whirlpool French Door Refrigerator filter needs a lot of maintenance to work correctly. So it needs to be checked regularly.

But talking about replacing the filter, the filter needs to be replaced after six months (200 gallons). 

Maintenance has a lot of benefits. Maintain your filter to get tasty, safe, and healthy water for drinking or making tea or coffee.

Related Article: Can You Use Whirpool Refrigerator Without a Water Filter

How To Know Water Filter Needs Replacing

By observing the following factors, you should come to know that it’s time to replace the filter:

  • The water in the refrigerator tastes terrible.
  • The smell of filtered water is peculiar.
  • Water pressure drops when it is dispensed.

Final Words

The whole information concludes that you should replace your refrigerator filter after 200 gallons (six months) to get tasty, safe, and healthy water.

Moreover, we have discussed the filter replacement procedure of all five filters. You can follow these steps to change your refrigerator water filter.

Leave a Comment